'Conveyor' Articles

We could speak volumes about the volumes the all-commodity AGI Batco UCX3 U-Trough Belt Conveyor can process. It’s powerful, high-capacity, and fast. In ideal conditions, it can move up to 12,500 bushels (about 340 tons) of canola in a single hour.

At that rate, it’s not sheer fantasy to imagine loading a Super B in 10 minutes. Even heavier crops like wheat and peas still whistle through at about 10,000 BPH.  



Fast as that ride might be, the cereals, pulses, oilseeds, or fertilizers you put through it come out hardly the worse for wear. Gentle handling is the beauty of a U-trough system – especially one with the UCX3’s problem-solving design. It focuses on eliminating points where spillage, crushing, and other damage can occur, from intake to spout.



Advanced Leakage Protection
That starts with the redesigned collapsible hopper. It’s built low, so you can be sure it will fit easily under any bin. The new, reinforced design also maximizes grain flow by minimizing potential leakage and grinding along its sides.



A double-lip sealed edge keeps your commodities tightly in place as they travel up the conveyor’s 15” Direct X belt. It’s a U-trough-ready update of the chevron pattern used in the successful AGI Batco BCX3 tube conveyor. 

Sticking With What Works
The BCX3 design worked so well that many of its features have been incorporated into, or adapted to, the UCX3. These include:

Turbo clean wash system, two belt scrapers, and belt brush. Working together in one remarkably easy clean-out process, they keep your belt debris-free and oilseed-friendly.



Redesigned S-Drive. Easily adjusted with normal tools, this feature keeps your belt running straight and true without the risk of overtightening your pinch-roller bearings. 

IBEX Mover Kit. Redesigned with a built-in braking system and a 160° turning radius, the IBEX is powerful and easy to maneuver whether you’re on a flat, dry surface or navigating deep muck. Two features provide the outstanding traction you’ll need to get you through a rain or snow-drenched day in your bin yard: Skid steer-style tires for better traction and single-wheel drop-and-go convenience and balance.



More Power to U. 
One notable difference between the U-Trough Conveyor and the BCX3 is the size of their engines. The BCX3 offers a choice of two gasoline engines – the 32HP Kohler or the 33HP EFI Vanguard. The UCX3 bumps the power up with a 40HP EFI Vanguard motor and upgraded drive components to further increase hydraulic performance and longevity. 



Learn what the UCX3 can do for you at Flaman.
Want to know more about the AGI Batco UCX3 U-Trough Conveyor? You can find expert advice at 11 Flaman dealers across Manitoba, Saskatchewan, and Alberta. Drop by your nearest Flaman location and get an up-close look at features like the ergonomic command centre, IBEX Mover Kit, and spillage control.



Ask our knowledgeable sales staff how the UCX3 or any of our other equipment can help your farming operation.  ...

With the cold weather snap we've been having, I'm reminded that my dad always said, "Things just start breaking down and don't work well after -25". That being said, you don't always have the luxury of taking a day off when the elevator calls for grain in the middle of winter. In case you're in a rush and it's too cold to fire up the auger to load the trucks, take a few minutes and remind yourself of a couple of key tips to ensure that your auger or conveyor starts when you need it to.

Fuel
Fuel problems always seem to show up when the cold hits. The two most common fuel problems are:
1. Old/dirty fuel
2. Water in the fuel...

It’s here. The legendary orange “gentle giant” from AGI/Batco has received more than a facelift for 2021. After a complete redesign from hopper to downspout, the BCX3 conveyor has a few new features worth bragging about. Aside from the redesigned S-Drive, new Turbo-Clean Wash System, and remodeled fuel tank, there are still 3 big upgrades that make this the most versatile conveyor yet.

...

The AGI Hutchinson Double Run Chain Conveyor is a brand new product to the Flaman lineup. It is built in Western Canada with the prairie farmer in mind. Manufactured at AGI’s plant in Swift Current, SK, it is designed to handle delicate crops grown on the prairies, like pulses, far more gently than an auger would.


The UHMW plastic paddles gently convey grain 

Maneuverable in Tight Spaces:
Modeled after the clean grain elevator on your combine, its UHMW plastic paddles convey crops to your bin in a gentle manner. A huge benefit of this is the ability to operate at full capacity from nearly any angle, fitting into tighter spaces.
Another feature of the Double Run is the easy to use swivel arc kit, which makes the unit highly portable around the yard.  You can move it from bin to bin or dryer, by simply swapping a few pins.   


The swivel arc kit allows for easy maneuverability 

Low Power Requirements:
While the Double Run is powerful in getting your grain into the bin, it has a low horsepower requirement compared to alternative grain handling equipment. As an example, 8” model with a length of 82’ requires just 18 HP at a 45° angle (see chart below).  These units are available with an electric motor or PTO drive, giving you plenty of power options.
 


Proven Reliability & Longevity:
We all know an unreliable auger can be a huge problem for your operation at harvest time.  The Double Run was designed as a solution to this problem.  The chain conveyor requires less maintenance and has more longevity than your typical auger. Keep the chain running straight and tensioned properly, and these units will just run. And run. And run. 



Travis Frey of AGI walks us through exactly what makes this unit different:
 

The Double run comes in lengths of up to 82’ on the 8” and 10” models, with up to 4,000 BPH capacity on the 8” and 6,000 BPH on the 10”. It is also available in a 12” model, which has a 10,000 BPH capacity and lengths up to 130’.
 

---

Stop by your local Flaman Ag store or give us a call for more information on this unit.

If you’ve ever moved grain with a conveyor or auger, you know that standard screw jacks can be inconvenient and a hassle to hook up and connect with your tractor. And if you’ve ever said to yourself “there has to be a better way,” then you’re not alone. The Lift-EZ Hydraulic Jack is a safe and convenient way to connect your auger or conveyor to your tractor
 
We spoke with the product’s inventor, Bret Watson, the operations manager at Flaman’s Swift Current location, about where the idea for this product came from, and why every farmer could use one.



Tell me where the idea for this hydraulic jack came from?
Bret: I invented it two years ago with Bob Schafer. Bob has a service company that deals with farmers, and his customers were having trouble with their jacks getting damaged. They needed another option.
Bob and I were having coffee one day and we said to ourselves, “this is something we could do.” Bob is a mechanic by trade, and I have an engineering degree and manufacturing background. Hydraulics are readily available on back of a tractor so that’s why we chose that route.

 
What was the creation process like?
Bret: We started with some drawings on a piece of paper, then I used CAD to develop it and make a prototype. Then we fine-tuned it to make sure it was user-friendly. From concept to completion it took about 3-4 months.
 
Tell me about the jack and what makes it different.
Bret: With this jack, the farmer can back up to auger/conveyor, connect the jack hoses and then safely lower/raise the unit from the cab of his/her tractor. They can easily get everything aligned, then slide in the implement pin, raise the Lift-EZ jack and then they’re good to go. It uses the hydraulics that tractors already have, so it’s easy to add on. I haven’t seen anything like this for farm use before.
 

Tell me about the added safety features of this hydraulic jack.
Bret: The jack comes with a hydraulic safety valve, so if there is any damage to any hydraulic hose the jack won’t come down. You can adjust the jack from your seat safely. When you get out of the tractor, you don’t have to worry about the jack creeping down, the valve locks it and won’t allow it to come down unexpectedly, which of course could be very dangerous.
 
Can this jack go on any auger or conveyor?
Bret: Yes, it can be retrofitted to any auger or conveyor. The jack stub can be mounted at any height in order to replace any standard screw jack. It’s very user-friendly.
 
What inspires you to invent products like this?
Bret: I’m driven by solving problems and safety. This product came right from a farmer’s need. It’s a safer product and something that will help them.


The Lift-EZ Hydraulic Jack will be available at most Flaman locations in Saskatchewan. Please call your local Saskatchewan store to ask about availability or to speak to a product specialist.